Factory-direct replacement parts for all PARAS® cream separator models — GR 7 to 5000 LPH. Discs, bowls, seals, bearings, gaskets, spindles, and complete service kits. Fast dispatch from Meerut across India and internationally.
All critical wear parts stocked for immediate dispatch. Contact factory with your model number for availability and pricing.
Conical separator discs are the core separation element. PARAS® discs are precision-stamped to exact tolerances for each model. Worn or damaged discs reduce separation efficiency and fat loss in skim milk. Available as individual discs or complete disc stack sets.
Food-grade rubber gaskets for the separator bowl, neck ring, and discharge ports. Replace gaskets annually or immediately when cream or milk leakage appears. Incorrect gaskets cause contamination and unsafe operation at high bowl RPM.
The main spindle and its precision bearings support the bowl at full operating RPM. Spindle wear causes vibration, noise, and separation inefficiency. PARAS® replacement spindles are precision-ground to original specifications — no machining required on installation.
Complete separator bowl bodies and neck rings for all GR-series models. Required when the bowl is cracked, warped, or damaged. Bowls are precision-balanced at the factory — never use unbalanced or repaired bowls in cream separators.
Worm gear, worm shaft, bevel gears, and clutch components for manual and electric-drive separators. Drive wear causes RPM drop and poor separation. Genuine parts maintain the correct gear ratio and bowl speed for each model.
Feed pump assembly, float valve, and flow-rate regulator for AEP pump-fed models (GR 109 AEP, GR 1 AEP, GR 2 AEP). Critical for maintaining consistent milk inlet flow and correct cream percentage in industrial AEP configurations.
Replacement electric motors and DOL starters for electric and dual-drive cream separators. PARAS® supplies matched motors for each model to maintain correct RPM and torque characteristics. Single-phase and three-phase options.
Pre-packaged annual maintenance kits containing all consumable wear parts for a single service cycle. Includes gaskets, seals, O-rings, and lubrication — everything needed for the recommended annual overhaul. Available for all standard GR-series models.
| Model | Capacity | Drive Type | Parts Availability | Product Page |
|---|---|---|---|---|
| GR 7 Series | 60 LPH | Manual / Dual-drive | Full parts range available | View model → |
| GR 8 Series | 80–100 LPH | Manual / Dual-drive | Full parts range available | View model → |
| GR 9 Series | 165 LPH | Manual / Dual-drive | Full parts range available | View model → |
| GR 11 Series | 300 LPH | Manual / Dual-drive | Full parts range available | View model → |
| GR 107 Series | 450 LPH | Electric / Dual-drive | Full parts range available | View model → |
| GR 108 Series | 600 LPH | Electric / Dual-drive | Full parts range available | View model → |
| GR 109 AEP/AET | 800 LPH | AEP pump-fed | Full parts + AEP pump components | View model → |
| GR 1 AEP | 1200 LPH | AEP industrial | Full parts + AEP pump components | View model → |
| GR 2 AEP | 2000 LPH | AEP industrial | Full parts + AEP pump components | View model → |
| GR A3 Online | 3000 LPH | Online continuous | Parts available — contact factory | View model → |
| 5000 LPH Online | 5000 LPH | Online auto-clean | Parts available — contact factory | View model → |
To order parts, call +91-9837043418 with your model name and component description. Parts are dispatched from our Meerut factory.
Cream separator bowls spin at 6,000–8,000 RPM. Even a small imbalance from an incorrect part causes severe vibration, bearing failure, and potential bowl ejection. Genuine PARAS® bowls are factory-balanced to zero tolerance.
Disc and gasket dimensions are specific to each model. A disc that's 0.1mm too thick changes the disc stack height and cream channel geometry — reducing separation efficiency and risking seal failure.
All genuine PARAS® milk-contact parts use SS 304 or approved food-grade rubber compounds. Aftermarket parts may use incorrect rubber grades that leach into cream or skim milk, creating food safety liability.
Use of non-genuine parts voids the manufacturer's warranty. Damage caused by incorrect spare parts is not covered. Genuine parts maintain your warranty validity for the full term.
International orders: specify country for correct shipping method and documentation.
Yes. PARAS® maintains parts availability for all currently manufactured models and most older GR-series models. Core components like discs, seals, gaskets, and bearings are stocked for GR 7 through GR 108. Contact the factory with your model number for specific availability.
Note your model number (on the nameplate — e.g. GR 108, GR 11, GR 1 AEP) and identify the component from your parts manual diagram. Contact the PARAS® factory with the model number and component position number or description for correct part identification.
The most frequently replaced components are: (1) Bowl gaskets and seals — replace annually or when leakage occurs; (2) Separator discs — when worn or damaged; (3) Main spindle bearing — every 2–3 years under heavy use; (4) Float valve assembly — in manual-feed models; (5) Cream regulation screw — in AEP models.
Yes. PARAS® ships spare parts to all export markets — Bangladesh, Nepal, Sri Lanka, Kenya, UAE, South Africa, and more. Parts are properly packed, labeled with HS codes, and dispatched via courier or freight. Call +91-9837043418 for international orders.
Cream separator bowls rotate at 6,000–8,000 RPM. Incorrect dimensional tolerances in aftermarket parts cause imbalance, vibration, and risk of bowl failure. Genuine PARAS® parts are manufactured to exact tolerances, ensuring safe operation, correct cream percentage, and maintaining warranty validity.
Fast dispatch from Meerut for all stocked parts. For industrial models and international orders, our team can confirm availability and dispatch timelines immediately.